---
title: "Cabling the Appliance to a Network"
canonical: "https://docs.infoblox.com/space/4000SeriesInstallGuide/37257286/Cabling%20the%20Appliance%20to%20a%20Network"
format: markdown
---
Use one or more Category 5/6 Ethernet cables to connect the Infoblox 4000 Series appliance to the network.

1. Connect an Ethernet cable from the LAN1 port on the Infoblox 4000 Series to the network switch or router, as indicated in *<span style="color: #0000ff">[Figure](#CablingtheAppliancetoaNetwork-bookmark48)</span>*[ ](#CablingtheAppliancetoaNetwork-bookmark48)*<span style="color: #0000ff">[12](#CablingtheAppliancetoaNetwork-bookmark48)</span>*.
2. (*Supported* *with* *IB-4010* *and* *PT-4000* *appliances*) To connect the Infoblox 4000 Series appliance for HA (high availability), connect the HA ports on both appliances to a switch on your network. The VIP (Virtual IP), LAN1, and HA port addresses must be on the same subnet and be unique for that subnet.

> Macro (anchor)

*Figure 12* *Cabling a Single* *Appliance and an* *HA* *Pair* *to a Network*


> Macro (drawio)

# > Macro (anchor)

Appliance–Network Connectivity

By default, an Infoblox appliance automatically negotiates the optimal connection speed and transmission type (full or half duplex) on the physical links between its LAN1, LAN2, HA, and MGMT ports and the Ethernet ports on a connecting switch or load balancer.  
 Occasionally, the appliances may fail to auto-negotiate that speed and type, and instead connect at lower speeds of either 100 or 10 Mbps using potentially mismatched full- and half-duplex transmissions. If this occurs, begin by determining whether there is a firmware upgrade available for the switch. If so, apply the firmware upgrade to the switch and test the connection. If that does not resolve the issue, manually set the ports on the Infoblox appliance and on the switch to make 1000-Mbps full-duplex connections. See the section *<span style="color: #0000ff">Modifying</span>* *<span style="color: #0000ff">Ethernet</span>* *<span style="color: #0000ff">Port</span>* *<span style="color: #0000ff">Settings</span>* in the *Infoblox* *NIOS* *Administrator* *Guide* for the steps to resolve the problem.  
 *(Applies* *to* *Infoblox* *IB-4010* *and* *PT-4000/PT-4000-10GE*) To ensure that VRRP (Virtual Router Redundancy Protocol) works properly, configure the following settings at the port level for all the connecting switch ports (LAN1, LAN2 and HA where applicable):

- Spanning Tree Protocol: Disable. For vendor specific information, search for "HA" in the Infoblox Knowledge Base system at [https://support.infoblox.com/](https://support.infoblox.com/)
- Trunking: Disable
- EtherChannel: Disable
- IGMP Snooping: Disable
- Port Channeling: Disable
- Speed and Duplex settings: Match these settings on both the Infoblox appliance and switch
- Disable other dynamic and proprietary protocols that might interrupt the forwarding of packets.

Use the Grid Manager from a management system to access, set up and administer the Infoblox appliance. For management system requirements and access instructions, see *<span style="color: #0000ff">[Accessing](https://infoblox-docs.atlassian.net/wiki/spaces/4000SeriesInstallGuide/pages/37257247)</span>*[ ](https://infoblox-docs.atlassian.net/wiki/spaces/4000SeriesInstallGuide/pages/37257247)*<span style="color: #0000ff">[the](https://infoblox-docs.atlassian.net/wiki/spaces/4000SeriesInstallGuide/pages/37257247)</span>*[ ](https://infoblox-docs.atlassian.net/wiki/spaces/4000SeriesInstallGuide/pages/37257247)*<span style="color: #0000ff">[Infoblox](https://infoblox-docs.atlassian.net/wiki/spaces/4000SeriesInstallGuide/pages/37257247)</span>*[ ](https://infoblox-docs.atlassian.net/wiki/spaces/4000SeriesInstallGuide/pages/37257247)*<span style="color: #0000ff">[4000](https://infoblox-docs.atlassian.net/wiki/spaces/4000SeriesInstallGuide/pages/37257247)</span>*[ ](https://infoblox-docs.atlassian.net/wiki/spaces/4000SeriesInstallGuide/pages/37257247)*<span style="color: #0000ff">[Series Appliance](https://infoblox-docs.atlassian.net/wiki/spaces/4000SeriesInstallGuide/pages/37257247)</span>*.

# > Macro (anchor)

SFP/SFP+ Installation and Removal Guidelines

After receiving a shipped Infoblox 4000 Series appliance with SFP or SFP+ support, install the transceivers into your appliance before turning power on to the system for the first time.  
 Should circumstances require you to ship an appliance to Infoblox for repair or replacement, *remove** all** SFP** or** SFP+** transceivers** from** your** appliance **before **shipping** it** back** to** Infoblox*. Keep your transceivers in your facility until the appliance is replaced or repaired and subsequently returned to you.