Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Component

Description

Hard Disk Drives

Four hot-swappable Infoblox data storage devices configured in a RAID 10 (Redundant Array of Independent Disks) array. Each disk drive has LEDs on the far left side of each drive carrier, that indicate the connection and activity status on the disk drive. The top LED flickers green when the disk drive is operational and performing read-write operations. The lower LED is dark (inactive) during all operations. Both drive LEDs are dark when the disk drive is not connected. You must use the Grid Manager UI or the NIOS CLI to verify disk operation. For more information, see Evaluating the Status of the Disk Subsystem.

On/Off Switch

A power switch to turn the power supply of the appliance on and off. The switch is hidden. Use a small blunt object, such as a paper clip, to gently push the switch.

Power LED

An LED that glows green when there is power to the appliance. When it is dark, the appliance is not receiving power, even if the power cable is plugged in. When it glows red, there is an error. Ensure that you power on the appliance through the On/Off switch using a small blunt object, such as a paper clip.

USB Port

Reserved for future use.

IPMI Port

Dedicated Ethernet port used for LOM (Lights Out Management) with specific releases of NIOS. The IPMI/LOM Port supports 10/100/1000 Mbps operations. Ensure that the IPMI port is properly connected to the network before you configure LOM through Grid Manager for remote management. The IPMI port auto-negotiates up to Fast Ethernet 1000BASE-TX speeds; ensure that the switch port to which the IPMI port connects will auto-negotiate to 1000 Mbps operation.

MGMT Port

A 10/100/1000-Mbps gigabit Ethernet port for appliance management, or for appliance services on the network. You enable the MGMT port and define its use through the Grid Manager after the initial setup.
The Advanced Appliance PT-2205 must be managed through its MGMT port.

LAN1 Port

A 10/100/1000-Mbps gigabit Ethernet port that connects the appliance to the network. You use the LAN1 port for initial appliance setup. The LAN1 port carries all traffic if you do not enable the MGMT and LAN2 ports. The passive node in an HA pair (supported in the Trinzic 2210 and 2220 appliances) uses this port to synchronize the database with the active node.

Console Port

A male DB-9 serial port for a console connection to change basic configuration settings and view basic system functions through the CLI (command line interface).
If your system lacks a DB-9 serial port, use a properly grounded USB-to-Serial dongle for connection to the serial console port. If the dongle is connected to a laptop, the laptop also must be properly grounded. Failure to do so may cause damage to the serial console port of the Infoblox appliance. Infoblox is not responsible for such damage. For DB-9 pin assignments, see Figure 3.

HA Port (Active for high availability in the TE-2215 appliances and
PT-2205)

A 10/100/1000-Mbps gigabit Ethernet port through which the active node in an HA (high availability) pair connects to the network using a VIP (virtual IP) address. HA pair nodes also use their HA ports for VRRP (Virtual Router Redundancy Protocol) advertisements.
ND-2205 and TR-2205 Reporting Models: The HA Port is inactive and reserved for future use. See Table 2 , SFP/SFP+ Interfaces Support Summary for appliance support details.

LAN2 Port

A 10/100/1000-Mbps gigabit Ethernet port that connects the appliance to the network. The LAN2 port is disabled by default. You enable the LAN2 port and define its use through the Grid Manager after initial setup.

UID Button

The unit identification button. When you press the UID button, the LCD panel on the front panel blinks and the UID LED on the rear panel glows blue. In a rack environment, the UID feature enables easier location of a server when moving between the front and rear of the rack. You can also identify the appliance through the Grid Manager and CLI command.

 The following figure depicts figures depict the front panels of the Infoblox 2205 series.

...

Models on which the port slots are located at the right

 

Models on which the port slots are located at the center without the drive bay door

...